- Accessories
- Airbag Reset Tools
- Automotive Repair Software
- Bike Programming
- Car Radio Tools
- Dash Tools (Mileage/Km Correction)
- Diagnostic Tools
- ECU Programming
- Emulators
- Immo Tools (Key Programmer)
- Industrial Equipment Programming Tools
- RocketDump Software
- Software & Licenses
- Tuning Tools
- Universal Programmers
- SALE
text_empty
T-CAN Tool for Tesla cars
Diagnostic and Programming Tool
for TESLA Car Model S, X and 3
T-CAN PRO has very fast developing software and hardware with small box interface. Can help you solve many problems with the TESLA car "Model S, X and 3".
T-CAN PRO can work with ECU TESLA Model S,X,3
- 2019.05.23 NEW SDM by BOSH Module X and 3 model (read,clear fault codes and R/W EEPROM clear CRASH log.)
- ALERTS – Alerts on CAN bus (read alerts codes updated BMS 2018.09.14 BETA STAGE !)
- BDY - Body controller on CAN bus
- DH - Door Handles - Learn Front Driver Side - CAN BDY -125 kbps (BETA Stage - added 15.07.2019)
- SDM – Supplemental Deployment Module S model (read,clear fault codes,clear CRASH log by Boot mode pin.)
- SDM by BOSH Module X and 3 model (read,clear fault codes and R/W EEPROM clear CRASH log.)
- SEC – Security controller (Add Keyfob Key)
- CP – Charging port.
- PARK2 – Parktronic sensors (read and decode fault codes,erase stored fault codes)
- THC – Thermal controller (Airpurge function)
- EAS-TAS – Tesla Airsuspension System (read,decode,erase fault codes,clear Crash event, exit service mode ) supported until 06.2016
- BMS – Battery control Module (reset alert warnings w163,w026,w152,w153,w023,read softpack)
- TPMS – Tyre Pressure (read sensor ID stored in memory it usefull if you need to make new non tesla sensor)
- ESP – Electronic stability system (read and decode fault codes,erase stored fault codes)
What is T-CAN ?
T-CAN PRO is hardware and software for Tesla car only
The software is nessesrey to work with harware !
H A R D W A R E
1. Car Programmer – plastic blue box with info label on top, inside is PCB (Printed Circuit Boards with semiconductors and SIM card). The device does not contain batteries
2. 2 Data cables (type: x437 and x437A) - these 2 cables are used to connect the car to the programmer
3. USB cable – this cable is using to connect the programmer to the PC or Laptop
S O F T W A R E
The software you need to work with T-CAN PRO programmer.
There is no other software.
The software is frequently updated, so it is recommended to check from time to time [ T-CAN PRO - DOWNLOAD SECTION ] to see if new software is available.
To buy the software you need to select it as an option
T-CAN PRO software screenshots







N O T I C E R E G A R D I N G S O F T W A R E
W A R N I N G !
DON'T BUY T-CAN PRO IF
R E T U R N

S U P P O R T !
Connector x437 or x437A (female) has to be plug into Tesla Diagnostic Connector (male)
If you do not know where is Diagnostic Connector, take a look on video below between 49 sec. - 1.10 mins.:
Work on the bench while developing the T-CAN tool
What you will receive after purchase ?




after shopping you will receive an email with licence file if you bought software - what you should do with that file can be find in manual (downloadable with T-CAN PACK software)
Download the PACK (software + drivers + manual)
Run it without installation and check the features and capabilities of T-CAN PRO
Related Products
Advanced Scooter Workshop (ASW)
Estimated date of the new delivery around the end of January 2019, but may be later You can sign up to receive our email newsletter and we'll let you know We only send information about our new prod..
Emulator ESL Renault CAN500
Emulator ESL Renault CAN500500kbs PLUG &PLAY Emulateur ESL renault CAN 500Kbit/s for Renault without cut CAN wires. The emulator is used to check the correctness of operation steerin..
RocketDump - software
RocketDump a tool to sort your files and useful tools ! RocketDump is automotive software, although is still young in the market today, RocketDump is necessary nonetheless among other solutions..